Ocdin Screen Protector for Omega x Swatch Speedmaster Moonswatch, Hydrogel TPU Soft Film for Acrylic Crystal (10)

First off, these screen protectors DO work. The protector is a thin flexible "hydrogel" like material that is soft enough to conform to the domed crystal of the MoonSwatch. The issue is...this protector is sandwiched between FRONT and BACK films, and due to its thinness and strong adhesive, is very hard to separate from the BACK film. This is the side you're supposed to peel off first (facing the crystal) - you will likely have inadvertently peeled off the protector with the BACK film at this step. This is evidenced by all the negative reviews where it appears that most have failed to put the actual protector onto the watch and are instead sticking the inflexible FRONT film on instead. Here is how I fixed that issue:1. Clean the crystal and keep it as dust free as possible. Use the stickers to pull extra dust off.2. Peel off the BACK film. This will contain both the protector and the BACK film. Keep the writing on the BACK pull tab facing the crystal. Place it over the watch crystal.3. Carefully remove the pull tab from the now separated FRONT film and stick it to protector sitting on the crystal. The newly placed FRONT pull tab should be facing you and the BACK pull tab should still be down facing the crystal.4. Hardest part - try to separate the protector with the FRONT pull tab and the BACK pull tabs. This could take a while. The protector IS there and if you give it some time it will begin to separate.5. As soon as the BACK film separates itself you will need to work fast to apply the protector. The film is thin and it will begin to curl up right away.6. Once applied you can remove the FRONT pull tab. There may be bubbles which will need to be squeegeed out. You can use either the FRONT or BACK films over the protector and use your nail to push out the air bubbles.Hope this helps!

The application stickers on the lenses protector would not come off without leaving adhesive residue on protector that wont come off. The instructions on container are for applying to a phone screen and not proper watch screen instructions. Overall very pitiful product.

Forget people on Reddit saying it’s silly to put a screen protector on a $250 moonswatch. This watch was hard to get, and it is very fragile. Do what makes you happy.These protectors work great on moonswatches. They do not cover the sides of the domed crystal, just the top surface - but they fit the top surface perfectly. So people saying it’s “too small” are probably expecting it to cover the whole dome. I’m fine with protecting the face, which is most vulnerable and visible.1 or 2 tiny bubbles are inevitable. You have to choose if you prefer some tiny nearly invisible bubbles, or constant scratches. Personal preference. But don’t expect zero bubbles unless you apply this under a microscope in a clean room.I needed 2 protectors to get it applied correctly, the first attempt had a big bubble that I couldn’t get out. Attempt two was way better.The protector has a film on both sides. If you put it on and it looks really crummy—you might still have the top film still applied. The actual protector is soft and flexible and nearly invisible.

Advertised to fit this brand of watch, it doesn’t. Sides stay up and I’ve used 2 out of the 4 given to you. This thing is awful and a waste of money. Directions are badly translated in English. Don’t get scammed.

The product is good, but the first 2 of the 5 protectors in the package pretty much had imperfections. The first one had dust on the sticky surface even before installing it. The 2nd one did not adhere to the watch. When the front protective plastic was peeled it came off with it. The 3rd one went on without a hitch. It came on nice, almost invisible. I just installed it last night, hopefully will last.I gave it 3 stars coz of the 1st 2 defective protectors.

Worked great on the first try. The bad reviews are people that didn't do it properly. There are some good instructions here in the comments to follow but I recommend watching a video on YouTube titled "How to Install the Tempered Glass Screen Protector & Camera Lens Protector" it shows a phone but the process is the exact same. It shows you how to clean, dry, pat with a dust absorber sticker, tape it down to align with the provided stickers and then you finally take the backing off and stick it on the watch. Since you left the front sticker you can just start pushing out the air bubbles with your fingers without worrying about smudges since you're about to peel that front sticker off too. It will be easy and perfectly aligned.I had a single stubborn bubble immediately after applying. I let it dissipate over night and a simple glide with the back of a finger nail over the surface in the morning resolved the bubble instantly.I would give it 5 stars except for the fact I bought a 5 pack and it only comes with cleaning wipes, dust absorber and alignment stickers for 2. Not a huge deal since a micro fiber cloth and some scotch tape will suffice or you can get crazy by not cleaning your brand new likely already dust free watch and freehand the alignment.

Worked exactly as I hoped it would. I work construction and ended up scratching the crystal on my Moonswatch pretty quickly. I found a post about this product on Reddit along with the suggestion to use Polywatch, an acrylic specific buffing compound.I first used the Polywatch to remove the sharp edges of the scratches (dont expect the deeper ones to completely disappear, that’s not how it works, it removes the sharp edges so that light doesn’t reflect off of it.) I then put on the screen protector and the scratches completely disappeared. It’s kept it from gaining new scratches and even if it did, they are incredibly easy to install so replacement is not an issue.When installing, watch the video in the product description first. You’ll see how to properly prep the surface and how to use the alignment stickers to aid in getting it on straight. Just take your time and do it in a well lit area. Any bubbles you may have after installation with disappear in a day or two.I highly recommend these protectors for Moonswatches.

La mica no pega para nada, no es del tamaño, solo desperdiciarás tu dinero. Pésima calidad y una estafa .

This product do work. I applied right after I took of factory film. If you apply phone screen protector before, this protect will be very simple to apply. I had one small bubble but went away next day and you won’t notice the film after you apply to your watch. I did it in one try. Great product.

Toughest part is getting it to line up nicely. I didn't have any problems with peeling it off like some of the other reviewers.

It is a good product to protect your watch.

Well package. Easy application. Will purchase again. Look forward for promo deals